- Equalizer hitch how to#
- Equalizer hitch install#
- Equalizer hitch manual#
Equalizer hitch how to#
lbs.Īnd here we are, done with the whole discussion on how to adjust equalizer hitch during installation.
Make the ¾ inch bolts tightened to not more than 200 ft. There should not be any gap in the washer stack. 
The angle set screw is tightened enough against the shank. You can also reduce space washers.Īs soon as you get the required weight distribution, make sure However, if you are trying to reduce the weight transfer or bring the tow vehicle to the rear-end below, try lowering the position of L-brackets. If you are trying to increase the weight transfer or bring the tow vehicle front end below, try elevating the position of L-brackets. Here’re how you can sort the trailer hitch adjustment issues It cannot have a difference of more than 1 inch. Your job is to make both compressions on the front and back equal. And here you have the two vehicle’s suspension compression references. Subtract the initial one from the new height. 
Now you need to take the measurement once again and call it the installed height, that you’d compare with the initial height. And you have recorded it previously as initial height. We already told you how to measure the reference point to the ground. Reference Points Re-measurement to Adjust If Required
Equalizer hitch manual#
You can check the details in the given manual for better reference. These are more installation-based procedures so we’re not going deep into it as equalizer hitch adjustments are what we discuss today. Next, you can couple the hitch ball of a trailer and follow up with attaching the spring arms to the brackets of the trailer.Make sure the arm is away from the frame of the trailer. Place the spring arm end into the hitch head’s arm socket and connect it with the socket pin as well as the socket clip.Here the bevel end will be entering the hole and securing the assembly’s backside with an L-bracket instead of setting screws going completely through the holes.
Equalizer hitch install#
Next, you want to install the L bracket using the set screw on the outer link plate. Make sure to tighten the bolts and also check that both outside and inside link plates have contact with the frame evenly. You’ll find the depth detail on this inside the equalizer hitch manual. Use the needed bolt for link plates to connect the assembly with the frame after marking the right spot. Install The Trailer Frame Plates, L-Bracket & Spring Arms 
Use a nut, lock washer, and flat washer of the same size.
And you also want to do this for the shank and hitch head channel hole. Into the ¾ inch flat washer, put the same size bolts. Consider the closest bolt hole for sliding the head of the hitch up or down next. Maintaining proper weight distribution hitch head angle is necessary. Make sure you hitch head on the shank and let the hitch ball be placed as well at the adjusted trailer height that you recorded earlier. Use five spacer washers after placing the spacer river. You should find around five holes on the hitch head channel, near the top side. Finally, you want to use the clip and receiver pin for consenting to the shank.įor Your Information – If there’s a need for a bigger height or drop with the hitch shanks, you can ask for one from the dealer and they may give you in case it's available. Make sure there’s enough ground clearance available. You can have it pointed up or down for obtaining the right ball height on this hitch shank. Place the adjustable hitch shank inside the receiver of the tow vehicle. Once you confirm that, here’s what to do next: Hitch Shank Installation & Adjustmentīear in mind that before you get into this step, it’s important to have the hitch ball installed. You should record this as the adjusted trailer height. 1-ton trucks are stiff suspension, you’ll need to add 1/8-inch hitch height. 3/4-ton trucks are average suspension, you’ll need to add 3/16 inches hitch height. Half-ton trucks are light suspension, you’ll need to add quarter inches hitch height. When you couple the trailer and tow vehicle, this adjusted trailer height will help in making the ride normal and comfortable.Ĭonsider the following equations for each addition of 100 pounds for trailer tongue weight. For the equalizer hitch adjustment, at this point, you need to add some height to the hitch ball so that the tow vehicle’s rear suspension can be compensated for a regular compression. This is the initial trailer hitch height. 
You want to measure the distance between the trailer coupler’s inside top part and the parking surface in inches.Make the trailer parallel to the ground using a trailer tongue jack.The height between reference point and pavement, measure and note it down.You want to determine the tow vehicle’s front and rear reference points.Take Accurate Baseline Measurements & Trailer Coupler Height
0 kommentar(er)
